Kensington and Chelsea · SW3

Plumbers in Chelsea

Tell us where you first saw water and whether you can still use the room. We’ll talk through what we can check before anyone lifts a tile or takes a panel off.

  • Separate leak tracing from making good
  • Plan access around the finishes you want to keep
Explore the services ↓
Bathroom with exposed cistern frame and bath before fitting

Which details help you price a concealed leak in Chelsea?

Tell us where the water first became visible, what was being used at the time and which inspection panels can already be opened. In a flat, include the building contact if the route could cross a shared wall or floor. We can then discuss the least disruptive starting point.

Can I combine a bathroom repair with replacement fittings?

Yes, tell us which item needs attention now and which changes you would like priced separately. A basin mixer, concealed shower valve and wall finish can have very different lead times. We can distinguish work needed to restore use from upgrades you may choose later.

Compact white boiler fitted between kitchen units

Existing finishes

Protect the room while we find the leak

For plumbing repairs in Chelsea, tell us which room you need back in use first. A concealed shower leak may call for a small inspection opening, while a dripping basin tap can often be assessed at the fitting. We can price the repair and the work to put the room back together separately so you can decide what to authorise before a finished surface is disturbed.

Before agreeing to open a tiled wall, identify any removable trim, service panel or access from the adjoining room. If a finish cannot be matched, the decision about opening it needs your agreement before the first cut. Keep a photograph of the original joint or panel position for reinstatement.

For this enquiry, see our leak investigation service.

Conservation area search ↗

Plumbing services in Chelsea

Choose the kind of work you need. When you get in touch, give us the full postcode so we can check your address.

Service van outside a London-style house

Urgent repairs

Emergency plumber

Tell us where the water is coming from and whether it is still running. We’ll check what we can reach, explain how we can stop the leak and tell you if we need to come back for a permanent repair.

Describe where water can be seen now, which fixtures are unusable and which controls have already been operated. Include the floor and the nearest accessible entrance. If someone else has isolated the supply, identify them so the plumber can establish what has been turned off and who else may be affected.

Explore emergency plumber →
Toilet and shower leaks

We look for when the leak starts. Water that appears while a shower runs leads us to different checks from water that appears when the tray empties. We agree any opening-up work with you first.

Record whether water appears while the cistern fills, immediately after flushing, during showering or some time afterwards. The position of a stain below can be misleading. Avoid opening up several finishes at once before agreeing which observation would narrow the investigation.

Explore toilet and shower leaks →
Tap repair and replacement

A tap can drip from the spout or leak underneath the sink. We check both ends before suggesting a new cartridge, a new connection or a replacement tap.

Water on the worktop may come from the spout, lever, tap base or splashing at the sink. Note when it appears and whether the underside of the worktop is wet. A clear photograph of the fitting and connections helps with the choice between investigation and replacement.

Explore tap repair and replacement →
Softener in a utility cupboard (illustration)

Water fittings

Saniflo installation

We check which fittings will drain into the pump, how high it needs to lift the waste and where the pipe will go. Once fitted, the pump must still be easy to reach and remove.

List every fixture intended to drain through the macerator and sketch the discharge route with its rise, bends and horizontal sections. Model limits govern the arrangement. A replacement with a similar footprint may still have different inlet positions and servicing requirements.

Explore saniflo installation →
Water softener installation

We look at the incoming water pipe, the drain and the space you need to add salt. Before fitting the softener, we agree which taps it will serve and show you how the bypass works.

Identify the incoming supply, proposed bypass and suitable drainage location. Include any outlet intended for unsoftened drinking water on the plan. Check that someone can actually open the salt lid and refill the unit when the cupboard is fully fitted out.

Explore water softener installation →
Radiator repair and installation

We check the radiator, its valves and the distance between the pipes. If you want a wider or heavier radiator, we’ll look at the wall fixings and explain whether the pipes need moving.

A wet patch at a valve may call for different work from corrosion on the panel itself. For a replacement, measure the wall space and note how far the old unit stands proud. Include the valve positions, skirting and nearby door swing in the discussion.

Explore radiator repair and installation →
Copper supply pipe and yellow isolation lever

Boilers & inspections

Boiler repair

Tell us what the boiler was doing when it stopped. We check how it responds to a call for heating or hot water and use the model details and fault message to narrow down the cause.

A photograph of the front panel is most useful alongside the exact appliance model and the time the problem occurred. An engineer investigating loss of hot water needs to know whether the fault affects a single shower, all hot taps or the hot water cylinder controls. Those are different investigation paths.

Explore boiler repair →
Boiler installation

We look at how you use heating and hot water before discussing a boiler size. The quote should show where the flue and drain will go, which controls are included and what we’ll test before handover.

Show the existing cylinder and controls along with the appliance. Discuss simultaneous showers, stored hot water and the available space before settling on a replacement arrangement. Moving the boiler may free a cupboard while adding a longer pipe route or a more difficult condensate connection.

Explore boiler installation →
Gas boiler service

We check and service the boiler using the instructions for that model. At the end, we explain what we found and whether a fault needs a separate repair.

A service booking starts with the appliance identity and its service history. Mention an intermittent shutdown or a recent change in pressure at the outset. That allows time for the engineer to explain whether the reported fault needs investigation beyond the routine maintenance visit.

Explore gas boiler service →
Gas safety certificates

Tell us which gas appliances are at the address and how we can get to them. The inspection record lists what was checked and what was found. We discuss any repair and return visit separately.

For each dwelling, write down its precise identifier, the appliances to be checked and how to reach them. Include appliances in cupboards outside the flat where applicable. Agree which contact can provide access and which person needs the resulting record.

Explore gas safety certificates →
Finished tiled floor (illustration)

Heating systems

Central heating installation

We plan where the radiators, pipes and controls will go. Before a floor is lifted, we agree which rooms we need to reach and how we’ll test the system before the boards go back.

Give each room a name that everyone on the project will recognise. Mark where radiators, valves and controls can remain accessible after wardrobes and doors are fitted. Agree the floor-opening sequence before other trades schedule carpets, joinery or decoration.

Explore central heating installation →
Central heating repair

One cold radiator calls for different checks from a whole house without heat. We start with the rooms affected and follow the controls and pipework before suggesting a repair.

A working radiator close to the boiler and several cold radiators further away tell a different story from no response anywhere. Give the room pattern to the engineer. If the property uses communal heat, establish the point where the dwelling’s controls and pipework begin.

Explore central heating repair →
Radiator powerflushing

Cold patches can have several causes. We check how water moves around the heating system before recommending a flush. A stuck valve or damaged pipe may need a different repair.

Describe the pattern of cold areas and any recent changes to the heating circuit. An assessment should consider whether circulation, controls or a faulty component better explains the symptom. The right outcome may be a repair or balancing work instead of a flush.

Explore radiator powerflushing →
Underfloor heating installation

We check the floor height, heat source and room controls. For water-based heating, we also plan where the pipes meet at the manifold and test the loops before the floor finish goes down.

Distinguish the whole room footprint from the area available for loops. Note fixed units, door thresholds, floor construction and planned floor covering. Record each room separately so the designer can relate usable area and heat demand to the proposed zones.

Explore underfloor heating installation →
Drain access beside a brick house

Drains & toilets

Clearing blocked drains

We ask which sinks, toilets or gullies are backing up and where we can reach the drain. After clearing it, we check the flow and explain whether a camera inspection would help if it blocks again.

Mark the sink, bath or external gully involved and describe which discharge causes water to rise elsewhere. That helps distinguish a restriction close to a fitting from a problem downstream of a junction. In a managed court, establish which inspection points are private or shared.

Explore clearing blocked drains →
Clearing blocked toilets

We check whether the blockage is in the toilet or further down the waste pipe. If the pan needs to come out, we’ll explain why and what putting it back involves.

A conventional WC discharging into a soil pipe calls for a different approach from a pumped toilet. Mention any motor housing or discharge pump you already know about. Tell us about wipes, toys or other objects that might affect the choice between clearance and retrieval.

Explore clearing blocked toilets →
Drain jetting

We look at the pipe and available access before deciding whether jetting is suitable. After the clean, we check that water runs through and discuss any section that still drains poorly.

The useful starting information is the inspection point, known pipe condition, access route and history of the blockage. Share any existing survey before arranging an attendance. A report of a displaced joint or damaged pipe changes the discussion about what jetting can achieve.

Explore drain jetting →
CCTV drain survey

A drain camera can show a damaged joint or an obstruction. We record where the camera went and how far it reached. If the pipe is blocked or underwater, part of it may need clearing first.

A builder planning an extension needs different information from an occupant reporting repeated loss of flow. Identify the section of interest, a recognisable start point and the intended use of the results. A long recording without a route reference can be difficult to relate to the proposed works.

Explore cctv drain survey →
Fixture detail for kitchen installations (illustration)

Kitchens & bathrooms

Bathroom installation

We check where the bath, shower, basin and toilet will connect. We agree who handles the tiling and waterproofing, and which joints need testing before the wall or floor is closed.

Draw the pan outlet, shower waste, bath taps and the wall that will carry any concealed fittings. Record the depth available under the tray rather than assuming the waste can pass beneath the floor. In a flat, establish whether the ceiling beneath belongs to someone else before proposing access from below.

Explore bathroom installation →
Kitchen installations

We check the sink and appliance positions against the water pipes and waste. We agree what needs doing before the cabinets go in and which fittings have to wait for the worktop.

Use the kitchen plan to mark the sink, dishwasher, washing machine and any separate drinking outlet. Give the plumber the proposed sink depth and waste kit, since storage drawers and bins compete for the space below. Agree first-fix positions with the kitchen fitter before units arrive.

Explore kitchen installations →
Dishwasher installation

We check the bay, water valve and waste connection. Once the machine is level, we watch it fill and empty. An integrated door or a hose trapped behind a cabinet can need extra fitting time.

Give the recess width, the machine’s installation drawing and a view into the adjacent sink unit. The supply and drain hose must reach usable fittings when the machine is fully back. The route also matters if a drawer runner or cabinet divider occupies the same space.

Explore dishwasher installation →
Washing machine installation

We check that the machine fits with its hoses connected and that it can be pulled out again. We level it and check for leaks while it fills and drains.

Measure the appliance depth as well as the opening width. Allow for the inlet hose, drain hose and socket arrangement behind or beside it. In an integrated installation, confirm that the furniture door can operate without shifting the machine forwards.

Explore washing machine installation →
Copper supply line and isolation valve inside the cabinet

Gas cooking

Gas cooker installation

We check the cooker model, the space around it and the connection. Once the engineer has fitted it, they check that it works and explain any changes needed before you use it.

Measure the narrowest usable width and note the worktop height, projecting handles and any wall units above. Supply the intended model drawing. A larger lid, different control position or dual-fuel specification can matter even if both cookers carry the same nominal width.

Explore gas cooker installation →
Gas cooker repair

Tell us which part of the cooker plays up. A hob that lights then goes out needs different checks from an oven that won’t heat. We check the model before quoting for parts.

A single hob burner failing to stay lit is a different report from the whole appliance losing ignition. Identify the setting and location involved, using the normal control labels if possible. Leave the cooker assembled so the engineer can assess the original arrangement.

Explore gas cooker repair →
Gas oven installation

We check the oven model against the cabinet, air gaps and connection. If the housing needs changing or an electrical connection needs arranging, we explain that before the old oven comes out.

A built-under oven and an oven in a tall bank may need different support and access. Show shelves, back panels and the available space beside the housing. Check the drawing for the exact appliance before a joiner cuts a ventilation opening or fixes the support shelf.

Explore gas oven installation →
Gas oven repair

Tell us whether the oven fails to light, cuts out or heats unevenly. We use the model details to plan the checks and explain whether the oven needs removing to reach a part.

Provide the setting used, approximate time from start and whether the problem occurs with every normal use. Mention if another cavity behaves normally. These observations can help separate a reported heating issue from a control, ignition or access problem requiring closer examination.

Explore gas oven repair →

Which finishes need protecting?

Choose the parts of the room we need to take care of.

Choose any that apply

What shapes your quote

Agree who protects finishes, handles panels and restores the surface.

Site protection
Opening and reinstatement
Materials
Confirm the selected model, fittings and availability before ordering.
Extra work
Agree any new access, parts or return attendance before proceeding.

How we approach a concealed repair

1234
  1. Visible finish
  2. Inspection access
  3. Service connection
  4. Reinstatement

Before we open a finished surface, we identify who can authorise access and how the opening will be made good. The quote can then distinguish the plumbing repair from work to tile, stone or joinery.

Inlet hose and washer (illustration)

Your questions in Chelsea

Can you keep the bathroom usable between visits?

Tell us if it is your only bathroom. We will identify which fixture can remain connected and when there must be a period without it.

Who replaces a decorative access panel?

Ask for removal, storage and reinstatement to be identified separately, particularly if the panel has a specialist finish.

Should I order a matching tap before the survey?

Keep the model reference and dimensions ready. The connections and available clearance should be checked before committing to an order.

Can the porter approve opening a wall?

A porter can facilitate entry. Identify the person authorised to approve intrusive work and spending before booking.

What if water has reached the room below?

Arrange contact with the occupant and building manager. Include both locations in the report so access can be coordinated.

Book Fanatic Plumbers in Chelsea

SW3 covers part of Chelsea. Tell us your street and what needs doing when you book.

Start an enquiry →

Plumbers nearby

Search all service areas

Ready to arrange a visit?

Tell us your postcode and what’s happening. We’ll discuss the next step.